Weishaupt WTC-GB 15-B Compact Installation And Operating Instruction Download Page 105

Page: 105 / 196

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

7 Commissioning

83309302 1/2018-05 La

105-196

7.2 Adjusting the condensing unit

Depending on system variation, specific commissioning steps are shown or hidden.

For cascade operation or multiple assignment, note deviating settings for commis-
sioning, see installation and operating manual Flue gas-air system.

During commissioning, make sure that:

maximum possible water throughput is ensured,
heat up is carried out with low flow temperatures and at low rating.

Open gas isolating valve.
Switch on system at switch S1 [ch. 5.7].

The commissioning wizard can be restarted at any time during the initial commis-
sioning.

Press dial knob for approx. 15 seconds.
The system device can be reset to its factory setting.
Reset device to factory setting.
The commissioning wizard restarts.

1. Set language

Select language required and confirm.
The language selected is generated.
The commissioning wizard starts.

Language

Deutsch

English

Français

Italiano

Español

Nederlands

OK = Press

Commissioning

The commissioning wizard guides you step
by step through the commissioning.

Select

and confirm.

2. Set date and time

Select

year

month

day

Press dial knob.
Selected area is highlighted in blue.
Set current date and confirm.
Select

and confirm.

Select

hours

minutes

Press dial knob.
Selected area is highlighted in blue.
Set current time of day.

Date

2016

June

Year

Month

Day

Time of day

Summary of Contents for WTC-GB 15-B Compact





































































































































































































Search results

Summary of Contents for WTC-GB 15-B Compact

Reviews:

Brands by name

Popular brands

Weishaupt WTC-GB 15-B Compact, Installation And Operating Instruction

Search results

Summary of Contents for WTC-GB 15-B Compact

Reviews:

Brands by name

Popular brands