manualshive.com logo in svg

Weishaupt WTC-GB 15-B Compact, Installation And Operating Instruction

The Weishaupt WTC-GB 15-B Compact is a high-quality heating system that ensures optimal comfort in any space. To easily set up and operate this product, download the free "Installation and Operating Instruction" manual from our website manualshive.com. It provides in-depth guidance for a hassle-free experience.

Share
Download
background image

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

10 Troubleshooting

83309302 1/2018-05 La

137-196

The following faults must only be rectified by qualified personnel:

Fault

Cause

Rectification

F 32

De-couple sensor (B2) defective

Check the sensor and cable and replace if neces-
sary

F 33

External sensor (B1) defective

Check the sensor and cable and replace if neces-
sary

F 34

DHW sensor (B3) defective

Check the sensor and cable and replace if neces-
sary

F 36

System pressure outside of range

[ch. 3.3.3.2]

Check system pressure, if necessary top up or
drain.

F 38

T1 sensor at additional module de-
fective

Check the sensor and cable and replace if neces-
sary

F 39

T2 sensor at additional module de-
fective

Check the sensor and cable and replace if neces-
sary

F 40

Internal pump signals electronic
fault

Check circulation pump, replace if necessary.

F 41

Gas valve control faulty

Check gas combi valve and cable, replace if ne-
cessary.

F 42

Internal pump signals blockade fault

Check circulation pump, replace if necessary.

F 43

Specified fan speed is not achieved

Check the fan and cable, replace if necessary.

F 44

Fan standby defective

Check the fan and cable, replace if necessary.

F 45

Valve flows out of tolerance

Check gas combi valve and cable, replace if ne-
cessary.

F 46

Multifunction sensor VPT defective

Purge system (heating circuit and DHW circuit).
Purge unit on the water side, initiate program

Automatic purging 

, see [ch. 6.6.9.6].

Increase system pressure.
Install the deaerator on site.
Check multifunction sensor VPT and cable, re-
place if necessary.

F 47

Multifunction sensor VPT version er-
ror

Version of multifunction sensor VPT not compatible
with appliance electronics WEM-FA-G

Replace multifunction sensor.

F 49

Data record error burner control

Interrupt the voltage supply temporarily
Carry out 

BCC Update

, see [ch. 6.6.9.6].

Replace appliance electronics WEM-FA-G if oc-
curring repeatedly.

F 50

Internal fault

Interrupt the voltage supply temporarily
Reset appliance, replace appliance electronics
WEM-FA-G if occurring repeatedly.

F 51

Data record error boiler

Interrupt the voltage supply temporarily
Carry out 

BCC Update

, see [ch. 6.6.9.6].

Replace appliance electronics WEM-FA-G if oc-
curring repeatedly.

F 52

Data record error burner

Interrupt the voltage supply temporarily
Carry out 

BCC Update

, see [ch. 6.6.9.6].

Replace appliance electronics WEM-FA-G if oc-
curring repeatedly.

F 53

Voltage supply outside the tolerance
limits

Check voltage supply

F 54

Electronic fault

Interrupt the voltage supply temporarily
Reset appliance, replace appliance electronics
WEM-FA-G if occurring repeatedly.

Summary of Contents for WTC-GB 15-B Compact





































































































































































































Reviews:

No comments

Related manuals for WTC-GB 15-B Compact

Samsung MIM-E03CN Installation And Maintenance Manual preview
MIM-E03CN
Brand: Samsung Pages: 27
iBath ALFA Instructions And Maintenance Instructions preview
ALFA
Brand: iBath Pages: 12
Raypak 5350 Series Installation And Operating Instructions Manual preview
5350 Series
Brand: Raypak Pages: 60
Caframo Pali 9510CA-BBX Operating Instructions preview
Pali 9510CA-BBX
Brand: Caframo Pages: 5
Vaillant geoTHERM SERIES Operating Instructions Manual preview
geoTHERM SERIES
Brand: Vaillant Pages: 112
Vaillant geoTHERM SERIES Installation Instructions Manual preview
geoTHERM SERIES
Brand: Vaillant Pages: 132
P.I.T. POG1100-P1 Operation Manual preview
POG1100-P1
Brand: P.I.T. Pages: 20
Amana PTH123G Manual preview
PTH123G
Brand: Amana Pages: 26
Warmlite WL41003Y Safety & Instruction Manual preview
WL41003Y
Brand: Warmlite Pages: 12
VOLTOMAT HEATING RAH-111956.2 Instruction Manual preview
RAH-111956.2
Brand: VOLTOMAT HEATING Pages: 104
SFA-SANIFLO SANISWIFT Installation And Maintenance Instructions Manual preview
SANISWIFT
Brand: SFA-SANIFLO Pages: 14
Nakayama PRO SP6200 User Manual preview
PRO SP6200
Brand: Nakayama Pages: 48
Sinbo SFH 3326 User Instructions preview
SFH 3326
Brand: Sinbo Pages: 40
Dimplex LA 17TU Installation And Operating Instructions Manual preview
LA 17TU
Brand: Dimplex Pages: 52
Reefe VSRM Series User Manual preview
VSRM Series
Brand: Reefe Pages: 14
XPOtool 63489 User Manual preview
63489
Brand: XPOtool Pages: 15
COSMOGAS GB 06 Manual preview
GB 06
Brand: COSMOGAS Pages: 182
Pittsburgh 45743 Owner'S Manual & Safety Instructions preview
45743
Brand: Pittsburgh Pages: 4

Brands by name

Popular brands

Load more brands