manualshive.com logo in svg

Weishaupt WTC-GB 15-B Compact, Installation And Operating Instruction

Share
Download
Weishaupt WTC-GB 15-B Compact Installation And Operating Instruction Download Page 154

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

12 Technical documentation

83309302 1/2018-05 La

154-196

12.5 Inputs/outputs

The inputs and outputs can be configured for various functions [ch. 6.6.9.5].

Depending on the hydraulic variant selected, the inputs and outputs are pre-as-
signed, the function can then not be changed [ch. 12.1].

WTC output MFA1, VA1 and VA2

Setting

Explanation

Off

Output not used.

Forward reporting of
operation

The contact closes as soon as a flame signal is present.

Safety valve Gas

The contact closes as soon as heat demand is present.

Forward reporting of
faults

The contact closes as soon as a fault occurs.

Actuator heating and
DHW mode

(1

The contact is closed during heating and DHW mode.

Actuator DHW mode

(1

The contact is closed during DHW mode.

Actuator heating mode

(1

The contact is closed during heating mode.

DHW 1: actuator

The contact is closed during DHW loading of DHW circuit 1.

Switched output via App

Variable contact via an App. Not supported in the current software version.

Pump neutralisation

The contact closes as soon as a flame signal is present.

(1

 Actuator: circulation pump or three-way valve

WTC input H1

The function (contact position) of input H1 can be rotated using parameter

 Input

H1 inverted 

.

Setting

Explanation

Off

Input not used.

System standby with
frost protection

The WTC is disabled for heating and DHW mode when the contact is closed.
Frost protection is activated.

Emergency-Off
heat exchanger

The system is disabled for heating and DHW mode when the contact is open.
Frost protection is not activated.
This function can be used to connect a temperature monitor, underfloor heating
circuit or safety switch of a condensate lift unit.

Block heating/
DHW mode

The WTC is disabled for heating and DHW mode when the contact is closed.
Frost protection is activated.

Generator block
heating mode

The WTC is disabled for heating mode when the contact is closed. Frost protec-
tion is activated.

Heating circuit 1:
standby

Heating circuit 1 is disabled for heating mode when the contact is closed. Frost
protection is activated.

Heating circuit 1: set-
back

When the contact is closed, the system heats to setback setpoint. The heating
program of heating circuit 1 is ineffective.

Heating circuit 1: nor-
mal

When the contact is closed, the system heats to normal setpoint. The heating pro-
gram of heating circuit 1 is ineffective.

Heating circuit 1: com-
fort

When the contact is closed, the system heats to comfort setpoint. The heating
program of heating circuit 1 is ineffective.

Heating circuit 1:
Emergency-Off

Heating circuit 1 is disabled for heating mode when the contact is open. Frost pro-
tection is not activated.

Heating circuit 1:
special level

When the contact is closed, the system heats to special level. The heating pro-
gram of heating circuit 1 is ineffective.

Forward signalling via
portal

When the contact is closed, a message is forwarded to the WEM portal.

Summary of Contents for WTC-GB 15-B Compact





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands