manualshive.com logo in svg

Weishaupt WTC-GB 15-B Compact, Installation And Operating Instruction

Share
Download
Weishaupt WTC-GB 15-B Compact Installation And Operating Instruction Download Page 60

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

6 Operation

83309302 1/2018-05 La

60-196

6.5.3 Heating circuits

Heating
circuits

A separate submenu appears for each heating circuit.

Parameters Setting

Operating
mode

determines the type of operation of the heating circuit.

If functions (heating, DHW) are deactivated in menu

 System operating mode 

, the setting has

effect [ch. 6.5.2].

Standby

:

Frost protection on
Heating off
DHW off

Time program 1 … 3

:

Frost protection on
Heating on
Temperature level according to selected time program. Time programs can be set in parameter

Heating program 

.

DHW on

(Factory setting: 

Time program 1

)

Summer

:

Frost protection on
Heating off
DHW on

Comfort, Normal, Setback

:

Frost protection on
Heating on
Temperature level according to the operating mode set, independent of the time program.
DHW on

Heating-
programs

The heating program is used to stipulate the times of the day when comfort, normal or setback heating
is used.

Time program 1 … 3

The preset time programs can be customised, factory setting see  [ch. 12.8].

Changing a time program:

Select time program using the knob and confirm.
Time bars are displayed.
Select week day(s) using the knob and confirm.
Time program can be edited.

The temperature of the level can be set using parameter

 Room setpoint temperature

.

Set time program required in parameter

 Operating mode 

.

Party/
Heating pause

The temperature level of the heating program can be temporarily changed (maximum 23:45 hours).
After this time the current heating program will be reactivated.

Select 

Function 

and set 

 Party/Heating pause 

.

Set level required in

 Room setpoint temperature 

.

Enter 

Start 

and

 End

.

If the parameter is set to

 Off

, the current heating program is activated.

(1

 Factory setting and setting range depending on the heating circuit type set [ch. 12.7].

Summary of Contents for WTC-GB 15-B Compact





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands