Weishaupt WTC-GB 15-B Compact Installation And Operating Instruction Download Page 62

Page: 62 / 196

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

6 Operation

83309302 1/2018-05 La

62-196

6.5.4 Domestic hot water

Domestic hot
water

Parameters Setting

DHW setpoint
temperature

DHW temperature for normal and setback operation.

Normal

(factory setting:

50 °C

)

Setback

(factory setting:

40 °C

)

Normal and setback operation can be assigned to specific times of the day using the DHW program.

DHW
Push

DHW Push is used to cover increased hot water demand, e. g. during setback operation.

The DHW tank is heated once to the DHW setpoint temperature set for normal operation.

DHW
program

The DHW program is used to stipulate the times of the day when the DHW tank is heated to normal
temperature or setback temperature, factory setting see [ch. 12.8].

Change a time program:

Select week day(s) using the knob and confirm.
Time program can be edited.

Circulation
program

The circulation program is used to stipulate the time of day when the circulation pump is switched on,
factory setting see [ch. 12.8].

Change a time program:

Select week day(s) using the knob and confirm.
Time program can be edited.

DHW
operating
mode

Deactivate DHW preparation.

(factory setting):

DHW preparation activated.

Off

DHW preparation deactivated.

6.5.5 Statistic

Statistic

In the

Statistic

menu, daily, monthly and annual values relating to the energy

generated are displayed.

Information Description

Energy
WTC
total

Total amount of heat generated by the condensing unit.

Summary of Contents for WTC-GB 15-B Compact





































































































































































































Search results

Summary of Contents for WTC-GB 15-B Compact

Reviews:

Related manuals for WTC-GB 15-B Compact

Brands by name

Popular brands

Weishaupt WTC-GB 15-B Compact, Installation And Operating Instruction

Search results

Summary of Contents for WTC-GB 15-B Compact

Reviews:

Related manuals for WTC-GB 15-B Compact

Brands by name

Popular brands