Weishaupt WTC-GB 15-B Compact Installation And Operating Instruction Download Page 145

Page: 145 / 196

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

11 Accessories

83309302 1/2018-05 La

145-196

Refitting

Replace seal

ensuring sealing surfaces are clean.

Refit externally powered anode in reverse order and:

place the green surface of the diode board

in such a way it faces nut

tighten screws with a torque of 8 Nm.

Fit inspection flange, tighten screws diagonally across (35 Nm +5).
Connect anode cable

CAUTION

Corrosion due to missing protective layer

Incorrectly connected externally powered anode does not form a protective layer. A
missing protective layer can lead to corrosions.

Correctly connect cable

Plug in mains adapter.
Control lamp on mains adapter illuminates green.
Check anode current (greater than 1 mA), enter value and date on label.
Enter completed service on label.
Refit front panel.

Summary of Contents for WTC-GB 15-B Compact





































































































































































































Search results

Summary of Contents for WTC-GB 15-B Compact

Reviews:

Related manuals for WTC-GB 15-B Compact

Brands by name

Popular brands

Weishaupt WTC-GB 15-B Compact, Installation And Operating Instruction

Search results

Summary of Contents for WTC-GB 15-B Compact

Reviews:

Related manuals for WTC-GB 15-B Compact

Brands by name

Popular brands