Weishaupt WTC-GB 15-B Compact Installation And Operating Instruction Download Page 39 | Manualshive

Page: 39 / 196

background image

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

5 Installation

83309302 1/2018-05 La

39-196

Check fresh water storage tank

Check inspection opening and connections are water tight.
Check operational readiness of safety valve by applying air.
Pressure test system until safety valve reacts.
If necessary, plug in mains adapter of externally powered anode.
Check anode current (greater than 1 mA), enter value and date on the enclosed
label.
Stick the label to a clearly visible area.

Fill heating circuit

WARNING

Contamination of drinking water

Topping up without system separator can contaminate the drinking water. A direct
connection between heating and drinking water is not permitted.

Top up heating water via system separator.

CAUTION

Damage to the unit due to unsuitable fill water

Corrosion and scale could damage the system.

Adhere to the requirements for the heating water and the local directives
[ch. 5.1].

Connect heating circuit flow to the siphon and open ball valve

1

.

Fit fill hose to heating circuit return and open ball valve

2

.

Flush the heating system with at least twice the total system content.
Contaminants are removed.
Close ball valve

2

.

Close ball valve

1

and remove connection to the siphon.

Check connections are tight.
Vent the heating system from bottom to top.

1

2

Pressure test

Before placing the condensing unit onto the fresh water storage tank, pressure
test the installation.
If the connections are leaking, the areas are easier to access.

«
...
37
38
39
40
41
...
»

Summary of Contents for WTC-GB 15-B Compact





































































































































































































Reviews:

No comments

Related manuals for WTC-GB 15-B Compact

Brand: Radiatori 2000 Pages: 2

Brand: Daikin Pages: 16

Altherma 3 H HT F Series

Brand: Daikin Pages: 256

Daikin Altherma 3 H F+W

Brand: Daikin Pages: 20

Brand: Daikin Pages: 68

Brand: Daikin Pages: 24

Brand: Daikin Pages: 36

Brand: Tandem Pages: 120

Brand: Vaillant Pages: 40

Brand: Zibro Pages: 64

Brand: Kärcher Pages: 16

Brand: ProMinent Pages: 20

Brand: Jaga Pages: 6

Nano-Flow 2,600

Brand: Cobalt Digital Inc Pages: 2

TURBO-FLUX modular

Brand: Cattani Pages: 61

Brand: Powerhorse Pages: 48

Brand: KISANKRAFT Pages: 44

Comfortstat 2 F 8ST

Brand: GDC Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands