WEICHAI WP6GTA Assembly/Disassembly Manual Download

Page: 73 / 90

Weichai America Corp.

8.2.3 Water Pump Assembly Procedure

Reverse the Disassembly Procedure to assemble the Water Pump.

8.2.4 Water Pump Inspection and Maintenance

Check the water pump gasket for any cracks or damage. Replace it if necessary.

Check the bolts and studs for any damage to the threads. Replace any if necessary.

Check water pump and middle cushion block for cracks. Replace them if necessary.

8.3

Thermostat Disassembly and Assembly

8.3.1 Thermostat Exploded View

Fig. 8-3 Exploded view of thermostat

8.3.2 Thermostat Disassembly Procedure

Loosen the clamps around the hose connecting the water pipe and thermostat. Remove the

hose.

Loosen the clamps around the hose connecting the thermostat and water pump. Remove the

hose and thermostat.

8.3.3 Thermostat Assembly Procedure

Reverse the Disassembly Procedure to assemble the Thermostat.

thermostat

hose

hose clamp

hose

Summary of Contents for WP6GTA



























































































Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands

WEICHAI WP6GTA, Assembly/Disassembly Manual

Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands