WEICHAI WP6GTA Assembly/Disassembly Manual Download

Page: 71 / 90

Weichai America Corp.

Cooling System

8.1

Cooling System Disassembly and Assembly

8.1.1 Cooling System Exploded View

The cooling system ensures that the engine can operate at the proper operating temperature.

Forced circulation cooling is most effective at keeping the engine within the normal operating

temperature range. The cooling system primarily consists of the water pump, fan, expansion

water tank, water tank and thermostat.

Fig. 8-1 Exploded view of cooling system

No.

name

No.

name

No.

name

radiator

Water pump

Intermediate plate

fan

Thermostat

Fan bracket

Water input pipe

8.1.2 Cooling System Disassembly Procedure

Remove the water tank.

Remove the fan.

Remove the belt.

Remove the generator and other auxiliary parts.

Summary of Contents for WP6GTA



























































































Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands

WEICHAI WP6GTA, Assembly/Disassembly Manual

Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands