WEICHAI WP6GTA Assembly/Disassembly Manual Download

Page: 40 / 90

Weichai America Corp.

Fig. 3-9 Exploded view of Torsional vibration damper Crankshaft belt pulley and Hub

3.6.2 Steps to disassemble torsional vibration damper and crankshaft belt pulley

loosen the bolt of crankshaft belt pulley, remove the crankshaft belt pulley and torsional vibration

damper in turn.

3.6.3 Steps to assemble torsional vibration damper and crankshaft belt pulley

Install the hub, torsional vibration damper and crankshaft belt pulley in turn when the timing gear

have been assembled.

Fix the hub on crankshaft with the hub fastening bolt. Crankshaft hub fastening bolts: Bolt

specification M16-12.9 (×4); Tightening torque: 300~310Nm; Test value: 300~360Nm.

Fix the crankshaft belt pulley and torsional vibration damper on the crankshaft hub with the

torsional vibration damper fastening bolts. Torsional vibration damper fastening bolts: Bolt

specification M10-10.9 (×6); Tightening torque: 65~70Nm; Test value: 65~80Nm.

3.6.4 Inspection and maintenance of crankshaft system

Check whether there is bump damage or deformation on the torsional vibration damper.

Check whether there is damage on the torsional vibration damper and whether there is

concussion on the bolt.

Check whether there is damage on the hub fastening bolt and torsional vibration damper

fastening bolt.

hub fastening bolt

crankshaft belt pulley

fastening bolt

torsional

vibration damper

hub

crankshaft timing

gear

crankshaft

Summary of Contents for WP6GTA



























































































Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands

WEICHAI WP6GTA, Assembly/Disassembly Manual

Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands