WEICHAI WP6GTA Assembly/Disassembly Manual Download

Page: 60 / 90

Weichai America Corp.

Remove the ignition coil.

Dismount the sparking plug with the wrench for the sparking plug.

Remove the ignition coil seat.

6.1.3 Ignition System Assembly Steps

Check the clearance of the sparking plug with a feeler, the clearance is 0.35mm.

Adjust the clearance of the sparking plug if it is not right. If the clearance of the sparking plug

is large, place the feeler in the gap first, then tap the electrode with a small wrench; If the

clearance is small, raise the gap with a small vise, then place the feeler in the gap, then tap the

electrode with a small wrench. When adjusting the clearance, ensure that the side electrode is

parallel to the center electrode.

Tighten the sparking plug with the sparking plug wrench after adjusting clearance.

Place the ignition coil and tighten the bolt of the ignition coil.

6.1.4 Ignition System Inspection and Maintenance

Professional tools for maintenance: the sparking plug wrench

Clearance of the sparking plug: adjust the clearance with the 0.35mm feeler

The torque range of sparking plug bolt: (25-28)Nm

6.2

Signal Generator Assembly and Disassembly

6.2.1 Signal Generator Exploded View

Summary of Contents for WP6GTA



























































































Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands

WEICHAI WP6GTA, Assembly/Disassembly Manual

Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands