WEICHAI WP6GTA Assembly/Disassembly Manual Download

Page: 45 / 90

Weichai America Corp.

Fig. 4-5 install direction of intermediate gear

Put the intermediate gear module in the front cover. Install the pin-shaft.

Insert the four M10 bolts after installing the washer. Torque the bolts to 65~70 Nm.

Rotate the gear by hand after tightening the bolts. Check the clearance and ensure the gear

turns smoothly.

4.3.4 Intermediate Gear Inspection and Maintenance

Check the bolts to ensure that they are threaded and tightened properly.

Check the tooth of the gear for any damage or sapling.

Check the intermediate shaft and the interface between the intermediate shaft and the bushing

or pin-shaft for any wear. Check the oil passage for any blockage.

4.4

Tappet and Pushrod Assembly and Disassembly

4.4.1 Tappet and Pushrod Exploded View

Summary of Contents for WP6GTA



























































































Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands

WEICHAI WP6GTA, Assembly/Disassembly Manual

Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands