WEICHAI WP6GTA Assembly/Disassembly Manual Download

Page: 78 / 90

Weichai America Corp.

Fig. 9-4 Exploded view of engine oil cooler

9.4.2 Steps to Disassemble Engine Oil Cooler

Loose the connecting bolts and take down the cooler, as shown in Fig..

9.4.3 Steps to Assemble Engine Oil Cooler

Check the cooler before assembling, make sure there is no manufacturing defect and damage.

Clean up the fitting surface between engine oil cooler and filter seat.

Install engine oil cooler and the connecting thread sleeve, tighten it.

9.4.4 Inspection and Maintenance of Engine Oil Cooler

Check the engine oil cooler for crack damage, replace it if necessary.

Check whether the oil cooler bypass valve has sluggish phenomenon, replace it if necessary.

9.5

Disassembly and Assembly of Main Oil Gallery Pressure Limiting Valve

9.5.1 Exploded View of Main Oil Gallery Pressure Limiting Valve

Summary of Contents for WP6GTA



























































































Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands

WEICHAI WP6GTA, Assembly/Disassembly Manual

Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands