WEICHAI WP6GTA Assembly/Disassembly Manual Download

Page: 21 / 90

Weichai America Corp.

2.8

Assembly and disassembly of oil sump.

4.2.8.1 Exploded view of oil sump.

Fig. 2-15 Exploded view of oil sump

2.8.2 Steps to disassemble oil sump.

Turn over engine to keep oil sump upward (key point 1)

Remove fixing bolts of oil sump.

Remove oil sump.

Remove the combination gasket and magnetic screw plug assembly

2.8.3 Steps to assemble oil sump.

Assembling steps are contrary to disassembling ones.

2.8.4 Inspection and maintenance of oil sump.

Key point 1:

Disassembling

Before the disassembling, all engine oil should be drained out. Put an engine oil container under

drain screw plug of oil sump, screw off the plug with a plug wrench to drain oil out.

Key point 2:

bolt

plug seat

seat

washer

oil pan

seat seal

washer

magnetic

plug

Summary of Contents for WP6GTA



























































































Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands

WEICHAI WP6GTA, Assembly/Disassembly Manual

Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands