WEICHAI WP6GTA Assembly/Disassembly Manual Download

Page: 77 / 90

Weichai America Corp.

9.3

Disassembly and Assembly of Engine Oil Filter

9.3.1 Exploded View of Engine Oil Filter

Fig. 9-3 Exploded view of engine oil filter

9.3.2 Steps to Disassemble Engine Oil Filter

Remove the filter with dedicated tool, as shown in Fig..

9.3.3 Steps to Assemble Engine Oil Filter

Check the O-shape seal ring of engine oil filter before assembling, make sure there is no

manufacturing defect and damage, replace the O-ring if necessary.

Tighten the filter according to the requirements on filter cap

9.3.4 Inspection and Maintenance of Engine Oil Filter

Check the engine oil filter assembly for damage, replace it if necessary.

9.4

Disassembly and Assembly of Engine Oil Cooler

9.4.1 Exploded View of Engine Oil Cooler

Summary of Contents for WP6GTA



























































































Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands

WEICHAI WP6GTA, Assembly/Disassembly Manual

Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands