WEICHAI WP6GTA Assembly/Disassembly Manual Download

Page: 44 / 90

Weichai America Corp.

4.3

Intermediate Gear Assembly and Disassembly

4.3.1 Intermediate Gear Exploded View

Fig. 4-4 Exploded view of intermediate gear

No.

name

No.

name

No.

name

Front end cover

Intermediate gear

shaft

washer

shaft

Intermediate gear

bolt

4.3.2 Intermediate Gear Disassembly Procedure

Locate the four M10 bolts to be removed.

Remove four bolts and the washer.

Insert a M8 bolt into the pin-shaft. Pull the pin-shaft out along this bolt. Take care to ensure

that the intermediate gear does not slide off and get damaged.

4.3.3 Intermediate Gear Assembly Procedure

Assemble the front cover according to the front cover assembly procedure (4.3.2).

Assemble the intermediate gear. Apply oil on the contact surface of the intermediate gear and

intermediate shaft. Pay attention to the direction of the intermediate gear:

Summary of Contents for WP6GTA



























































































Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands

WEICHAI WP6GTA, Assembly/Disassembly Manual

Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands