WEICHAI WP6GTA Assembly/Disassembly Manual Download

Page: 84 / 90

Weichai America Corp.

Fig. 11-2 Exploded view of generator

11.2.2 Alternator Disassembly Procedure

Remove the alternator lock nut to loosen the belt if it has not already been removed. Remove

the belt from the alternator pulley.

Remove the ground cable and the battery cable from the alternator.

Remove all bolts bolting the alternator to the bracket. Remove the alternator from its bracket.

Remove the four hex bolts bolting the alternator bracket to the engine block. Remove the

alternator bracket from the engine block.

11.2.3 Alternator Assembly Procedure

Reverse the Disassembly Procedure to assemble the Alternator.

11.2.4 Fault diagnosis and maintenance of alternator

1. Fault diagnosis process for alternator

bolt

bracket

bolt

lock nut

tighten bolt

Hexagon bolt

alternator

Summary of Contents for WP6GTA



























































































Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands

WEICHAI WP6GTA, Assembly/Disassembly Manual

Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands