WEICHAI WP6GTA Assembly/Disassembly Manual Download

Page: 17 / 90

Weichai America Corp.

Fig. 2-11 exploded view of front oil seal and rear oil seal

2.6.2 Steps to disassemble front and rear oil seal

Remove gear housing plate

Remove engine front oil seal

Remove engine rear oil seal cover (Key point 1)

Remove engine rear oil seal (key point

2.6.3 Steps to assemble front and rear oil seal

Assembling steps are contrary to disassembling ones.

2.6.4 Inspection and maintenance of engine front and rear oil seal.

Key point 1:

Inspection

Check whether the junction surface between rear oil seal cover and engine body is cleaning or

knocking wound.

Assembling

(1) Clean the junction surface and install 2 pins into engine body.

(2) Apply sealant on the junction surface of rear oil seal cover.

Summary of Contents for WP6GTA



























































































Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands

WEICHAI WP6GTA, Assembly/Disassembly Manual

Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands