WEICHAI WP6GTA Assembly/Disassembly Manual Download

Page: 70 / 90

Weichai America Corp.

bolt

cross pipe

bolt

bracket

O-ring

bracket

EPR valve

nut

bolt

electromagnetic

valve

7.3.2 NG Gas Supply And Gas Flow Control Valve (EPR Valve) Disassembly Procedure

Remove the bolt (2)

Remove the bolt (5)

Remove the bolt (14)

Take the EPR valve (4)

Take the bracket (3)

Remove the bolt (7)

Remove the cross pipe (6)

Remove the bolt (11)

Remove the electromagnetic valve (10)

10.

Remove the bolt (12)

11.

Take the bracket (13)

7.3.3 NG Gas Supply And Gas Flow Control Valve (EPR Valve) Assembly Procedure

Reverse the disassembly procedure to assemble the NG gas supply and gas flow control valve

(EPR valve)

7.3.4 Fuel System Inspection and Maintenance

Change the gasket and O-ring after disassembling.

Check the joint and clamp, make sure that they are tightened well.

Check the balance tube of the LPG evaporator..

Inspect the inlet pressure of the NG, the right pressure is 2.5kpa.

Inspect the joint of the gas path, make there is no leakage.

Summary of Contents for WP6GTA



























































































Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands

WEICHAI WP6GTA, Assembly/Disassembly Manual

Search results

Summary of Contents for WP6GTA

Reviews:

Related manuals for WP6GTA

Brands by name

Popular brands