VSCOM NetCom Plus 111 User Manual Download Page 29

Page: 29 / 133

4 Windows Virtual COM Driver

4.1.1.1 User Account Control (UAC)

In modern versions of Windows OS typical configurations

require to confirm the start of software to change the system configuration.

(a) UAC in Windows 7

(b) UAC in Windows 10

Figure 16: User Account Control

Since a change of system configuration is intended by the driver installation, confirm to start the
software.

Figure 17: NetCom

Driver Installation

4.1.1.2 Methods of Installation

The installation program offers three different ways of installa-

tion. The first option is the most common used function, a

Complete Installation

. All driver

September 2016

NetCom Plus User Manual

Summary of Contents for NetCom Plus 111






































































































































Search results

Summary of Contents for NetCom Plus 111

Reviews:

Related manuals for NetCom Plus 111

Brands by name

Popular brands

VSCOM NetCom Plus 111, User Manual

Search results

Summary of Contents for NetCom Plus 111

Reviews:

Related manuals for NetCom Plus 111

Brands by name

Popular brands