background image

77

and lubrications generally should be performed most frequently possible than 
prescribed in the preventive maintenance chart.

•  Always when oil level check and drainage plugs are removed, is is 
recommended to use adequated keys in order to avoid damage of the plugs, 
the same in case of the ring gasets replacement. 

WEIGHTS AND CAPACITIES

IMPORTANT:  The load limit must be observed according to the 

maximum capacity identification. Non-observance of these weght and 
capacity limits will cause the immediate cancellation of the product’s 
warranty.

NOTA: See the item Specifications.

ELECTRIC SYSTEM

PRECAUTIONS WITH THE ELECTRIC SYSTEM

• Do not invert polarity of the batteries;

• Do not use the battery charger to aid starting of the engine. If necessary, 
use only charged auxiliary batteries connected in parallel to aid the 
starting. 

•  Never perform adjustments on the cables connected to the control 

electronic module;

• Do not add the master key in the electric circuit supplying the electric module;

• If it is necessary to disconnect or connect the electric module, keep the ignition 
key in the switching-off position.

PRECAUTIONS WITH ELECTRICAL WELDING

• Before performing electrical welding in any part of the vehicle, disconnect the 
cables from the batteries. Check if the ground cable of the welding equipment 
is right on the component to be welded.

•  Do not perform electric welding near electric harness. Remove every 
component, if it is necessary to perform welding

IMPORTANT: When performing welding operations on the structure, 

previously disconnect all the electric cables from the panel to avoid damages 
of these components. 

• Before performing electrical welding in any part of the vehicle, disconnect 
the cables from the batteries and the connectors from the electric module. 
Check if the ground cable of the welding equipment is right on the component 
to be welded. 

• Do not perform electric welding near the electric module, actuators, 
sensors and electrical harness. Remove every component, if it is necessary 
to perform welding.

Summary of Contents for Marcopolo





























































































































Reviews: