Vislink HDT-1000 User And Technical Manual Download Page 9

Page: 9 / 62

Page

HDT-1000 User and Technical Manual

Indicator LED Table

Indicator

Description

Suggested Actions

PRESET

Displays the selected PRESET

[1 - 16].

Select the desired PRESET.

AUDIO

Green when enabled. Dark when

disabled. M=MIC L=LINE

Select the desired AUDIO setting.

RF HI

Green when radio power output is

set to high. Dark when set to low

power.

Select the power level required to optimize the

link.

VID

Green when a valid video signal

is present. Dark when no valid

video signal is present. Valid

video can be NTSC or PAL analog

composite, as well as ASI or HD-

SDI digital signal.

Check the video camera/source and cabling

to ensure the video signal is reaching the

transmitter. The Signal has to match what preset

is selected and what is configured in that preset.

ALARM

Red when an alarm occurs. Dark

when no alarm present.

Connect transmitter to PC via the Ethernet

interface to diagnose the source of the alarm.

CRYPTO

Green indicates encryption

is enabled and transmitter is

transmitting the encryption code

associated with the preset. Dark

indicates encryption is disabled.

Verify whether encryption is required for the

selected preset.

Verify that

encryption is properly configured.

Summary of Contents for HDT-1000































































Search results

Summary of Contents for HDT-1000

Reviews:

Related manuals for HDT-1000

Brands by name

Popular brands

Vislink HDT-1000, User And Technical Manual

Search results

Summary of Contents for HDT-1000

Reviews:

Related manuals for HDT-1000

Brands by name

Popular brands