Vislink HDT-1000 User And Technical Manual Download Page 16

Page: 16 / 62

Page 16

HDT-1000 User and Technical Manual

Internet

Gateway

192.168.50.1

Transmitter

192.168.50.10

Obtain an IP Address

Automatically (DHCP)

DC Power

To setup your HDT-1000 network for Livestream video broadcasting, complete the

following steps.

You must first setup a Livestream account and have the login information handy.

2. Set your PC to

Obtain an IP Address Automatically

[DHCP].

3. Determine the IP address of your Gateway using

Advanced IP Scanner

necessary. We will assume the Gateway address is 192.168.50.1 for this example.

Set your Transmitter’s IP address to a number inside the same network as the

gateway. We will assume the Transmitter address is set to 192.168.50.10 for this

example.

5. Connect an Ethernet cable to the Transmitter’s front panel RJ-45 ETHERNET

connector and to your router or gateway device.

6. Connect a second Ethernet cable to an available Ethernet Port on your Windows

PC and to your router or gateway device.

Connect your camera or video source to the Video IN connector on the Transmitter.

8. Connect the AUDIO/DATA System I/O cable Audio or MIC input connectors to your

audio equipment if you are planning to use audio.

Connect the DC Power In cable from your +11 - 32 VDC power source to the front

panel DC PWR connector. Allow 60 seconds for the transmitter to fully start-up.

10.

Navigate the Web Browser Control Interface to the Livestream page and configure.

Livestream

Go to

www.livestream.com

setup your free or premium account.

Go to pages 32-35 for Livestream

settings in the Web Browser Control

Interface

Summary of Contents for HDT-1000































































Search results

Summary of Contents for HDT-1000

Reviews:

Related manuals for HDT-1000

Brands by name

Popular brands

Vislink HDT-1000, User And Technical Manual

Search results

Summary of Contents for HDT-1000

Reviews:

Related manuals for HDT-1000

Brands by name

Popular brands