Vislink HDT-1000 User And Technical Manual Download Page 37

Page: 37 / 62

Page 37

HDT-1000 User and Technical Manual

HDT-1000 Screen:

Modulation Settings

Menu Path:

Presets

Modulation Settings

Type

[Modulation Settings

Section]

Select the desired RF output from the

Type

drop down menu:

COFDM-

DVB-T

SCM-Q

LMS-T

Modulation

[Modulation

Settings Section]

Select the desired waveform from the

Modulation

drop down menu:

QPSK

16QAM

64QAM

8-PSK

FEC

[Modulation Settings

Section]

Select the desired Forward Error Correction setting from the

FEC

drop down

menu:

1/2

2/3

3/4

5/6

7/8

RS Only

Guard Interval

[Modulation

Settings Section]

Select the desired setting from the

Guard Interval

drop down menu:

1/4

1/8

1/16

1/32

DVB-T Bandwidth

(Modulation Settings Section)

Select the desired setting from the

DVB-T Bandwidth

drop down menu:

MHz

7 MHz

8 MHz

SCM-Q Bandwidth

(Modulation Settings Section)

Select the desired setting from the

SCM-Q Bandwidth

drop down menus.

Note that there is a decimal point between the menus and the step size is 250

kHz. The number selected is in MHz.

Apply

[Modulation Settings

Section]

Click the

Apply

button to set the new information in the Modulation Settings

Section to the transmitter.

Summary of Contents for HDT-1000































































Search results

Summary of Contents for HDT-1000

Reviews:

Related manuals for HDT-1000

Brands by name

Popular brands

Vislink HDT-1000, User And Technical Manual

Search results

Summary of Contents for HDT-1000

Reviews:

Related manuals for HDT-1000

Brands by name

Popular brands