Vislink HDT-1000 User And Technical Manual Download Page 23

Page: 23 / 62

Page 23

HDT-1000 User and Technical Manual

RangeMaster

™

RangeMaster is a Vislink exclusive technique that maximizes the transmission range.

RangeMaster can send video signals up to four times farther than COFDM/DVB-T

transmission.

To set-up RangeMaster in your HDT-1000 transmitter, complete the following steps.

1. Select

Preset

Modulation Settings

from the menu bar. The

Modulation

Settings

screen displays.

2. Select

SCM-Q

from the

Type

drop-down list.

Select

1/2

RS only

from

FEC

drop-down list.

NOTE

FEC RS only in the HDT-1000 is the same as FEC 1/1 in the HDR-1000.

4. Make your other selections under

Modulation Settings

Make sure your HDR-1000 receiver is configured with matching settings.

6. Click the

Apply

button.

Summary of Contents for HDT-1000































































Search results

Summary of Contents for HDT-1000

Reviews:

Related manuals for HDT-1000

Brands by name

Popular brands

Vislink HDT-1000, User And Technical Manual

Search results

Summary of Contents for HDT-1000

Reviews:

Related manuals for HDT-1000

Brands by name

Popular brands