Vislink HDT-1000 User And Technical Manual Download Page 6

Page: 6 / 62

Page

HDT-1000 User and Technical Manual

Band and Frequency Options

HDT-1000 T

X models are available for a variety of bands:

HDT-1000P

P band

300—400 MHz

HDT-1000L

L band

1.7—1.9 GHz

HDT-1000S

S band

2.0—2.5 GHz

HDT-1000C1

C1 band

3.1—3.6 GHz

HDT-1000C2

C2 band

4.4—5.0 GHz

HDT-1000C3

C3 band

6.4-7.1 GHz

Unlicensed operation under FCC Part 15 in S Band is factory limited to 2.414 - 2.458

GHz.

Check your model number for the operating band of your HDT-1000.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: [1] This device may not cause harmful interference, and [2] this

device must accept any interference received, including interference that may cause

undesired operation

Operation

Antenna

[

SMA

]

Connects to SMA (female) connector cable [50 Ohm].

Provides RF output to antenna.

Video Input 1

[

BNC

]

Connects to 75 Ohm female BNC connector cable. Carries

video input from the camera/video source.

Ethernet

[

Network RJ-45

]

Connects to RJ-45 connector. Supports web browser

control interface. It is also used for IP streaming data output.

System I/O

[

Audio/Data 21-Pin

]

Connects to 21-pin System I/O connector [female]. Provides

audio in and RS-232 interconnections to [optional] telemetry

unit and/or Windows PC [for configuring channels].

Power

[

Lemo

]

Connects to the 4-pin Lemo DC input cable. There is no

power switch on the unit; it operates when connected to DC

power.

Input Voltage:

+10 to +32 VDC

Power Consumption:

10 W [nominal]

Summary of Contents for HDT-1000































































Search results

Summary of Contents for HDT-1000

Reviews:

Related manuals for HDT-1000

Brands by name

Popular brands

Vislink HDT-1000, User And Technical Manual

Search results

Summary of Contents for HDT-1000

Reviews:

Related manuals for HDT-1000

Brands by name

Popular brands