Vislink HDT-1000 User And Technical Manual Download Page 4

Page: 4 / 62

Page

HDT-1000 User and Technical Manual

Quick Start

Connect your resonant antenna to suitable 50 Ohm SMA connector cable and

connect to transmitter

ANT

[RF Output] connector.

Connect your camera or other video signal source to suitable 75 Ohm BNC

connector cable and connect to transmitter

Video 1

input connector.

Connect an Ethernet cable to the front panel RJ-45

ETHERNET

connector and to

an available Ethernet Port on your Windows PC.

4. Connect the

AUDIO/DATA

System I/O cable

Audio or

MIC

input connectors to

your audio equipment if you are planning to use audio.

5. Connect the

RS-232 Data

connector [System I/O] to your telemetry controller or

other device if you plan to transmit serial data.

6. Connect the

RS-232 Control

connector [System I/O] to your PC if you wish to use

serial link control.

7. Connect the DC

Power In

cable from your +11 - 32 VDC power source to the front

panel

DC PWR

connector. Allow 60 seconds for the transmitter to fully start-up.

NOTE

There is no ON/OFF Switch. Transmitter is ON when power is supplied.

Select your desired channel using the Preset and UP/Down buttons [see Main

Control Panel section]. Press the Save button.

If required, refer to Web Browser Control Interface section for Preset configuration

instructions. For special Livestream setup, see page 16.

Power

Ethernet

to PC

Antenna

Video 1

RS-232

Control

RS-232

Data

Mic 1

Mic 2

Audio

B Video

System I/O

(Audio/Data)

Summary of Contents for HDT-1000































































Search results

Summary of Contents for HDT-1000

Reviews:

Related manuals for HDT-1000

Brands by name

Popular brands

Vislink HDT-1000, User And Technical Manual

Search results

Summary of Contents for HDT-1000

Reviews:

Related manuals for HDT-1000

Brands by name

Popular brands