Vislink HDT-1000 User And Technical Manual Download Page 53

Page: 53 / 62

Page 53

HDT-1000 User and Technical Manual

Decoding two streams over IP using VLC

Complete the following steps to decode two streams over IP using VLC Media Player.

1. VLC Media Player is a free, easy-to-use utility for decoding media streams including

H.264. Download the VLC Media Player at

http://www.videolan.org/vlc/

2. Follow the installation instructions given with VLC.

3. Ensure that you have a GOP Length that is greater than zero on the Transmitter

Encoder Settings

screen (

Presets > Video Settings

4. Set transmitter output to Transport Stream over Ethernet (

Encoder Settings > Output

> TS over Ethernet

). Click the

Apply

button.

5. Start VLC Media Player. Select

Media > Open Network Stream

On the Network tab enter the Network URL: udp://192.168.1.105:1234 (this should

match the client IP address in the HDR-1000 Receiver

Presets > View/Edit > Video

Output > Client IP Address

7. Verify stream information in VLC by selecting

Tools > Codec Information > Codec

Details

Select either of the two video streams from the VLC

Playback

menu.

NOTE

Do NOT set GOP Length to 0 (Transmitter Encoder Settings) when

using VLC Media Player. Setting GOP Length to 0 may cause VLC to perform

intermittently.

Summary of Contents for HDT-1000































































Search results

Summary of Contents for HDT-1000

Reviews:

Related manuals for HDT-1000

Brands by name

Popular brands

Vislink HDT-1000, User And Technical Manual

Search results

Summary of Contents for HDT-1000

Reviews:

Related manuals for HDT-1000

Brands by name

Popular brands