Vislink HDT-1000 User And Technical Manual Download Page 33

Page: 33 / 62

Page 33

HDT-1000 User and Technical Manual

HDT-1000 Screen:

Livestream

[CONSULT FACTORY]

Menu Path:

System > Livestream

[Go to

www.livestream.com

for more information.]

Automatically Add

Recordings to On-

Demand Library

[Configure

Livestream Tab, Livestream

Channel Settings Section]

Click the

Automatically Add Recordings to On-Demand Library

checkbox

to setup Livestream for automatic adding of your recordings to your on-

demand library for later viewing.

Automatically Add

Recordings to Auto-Pilot

[Configure Livestream Tab,

Livestream Channel Settings

Section]

Click the

Automatically Add Recordings to Auto-Pilot

checkbox to setup

Livestream for automatic adding of your recordings to Auto Pilot for later

viewing.

Aspect Ratio

[Configure

Livestream Tab, Livestream

Channel Settings Section]

Select

3:4

16:9

from the dropdown menu to select your

Aspect Ratio

Bitrate

[Configure Livestream

Tab, Livestream Channel

Settings Section]

Select your desired

Bitrate

from the dropdown menu.

500 kbps

is the

recommended setting.

Apply

[Configure Livestream

Tab]

Click the

Apply

Button to set the changes to Livestream.

Summary of Contents for HDT-1000































































Search results

Summary of Contents for HDT-1000

Reviews:

Related manuals for HDT-1000

Brands by name

Popular brands

Vislink HDT-1000, User And Technical Manual

Search results

Summary of Contents for HDT-1000

Reviews:

Related manuals for HDT-1000

Brands by name

Popular brands