Vision Research Phantom Flex4K Manual Download Page 70

Page: 70 / 94

Phantom Flex4K Manual

Recommended batteries

A Flex4K and CineMag when running at maximum speed
can consume close to 140 watts of power.

When using batteries in the 12-14.4V range Vision
Research recommends only high capacity batteries which
can supply at least 10 Amps (at 14V) when fully charged.

Battery power can be continuously monitored on the
on-screen display and the side camera screen.

At the time of writing, Vision Research has verified the
following batteries:

Hawk Woods Reel Power (26V). The RP100 model will
run the camera approximately 45 minutes

Anton Bauer Dionic HD: Approximately 1 hour

Anton Bauer Hytron 140: Approximately 1 hour

BLUESHAPE 270HD (V-Lock): Over 2 hours

To change batteries without powering down
the camera, connect the 3-pin power cable
to a suitable power source.

Summary of Contents for Phantom Flex4K































































































Search results

Summary of Contents for Phantom Flex4K

Reviews:

Related manuals for Phantom Flex4K

Brands by name

Popular brands

Vision Research Phantom Flex4K, Manual

Search results

Summary of Contents for Phantom Flex4K

Reviews:

Related manuals for Phantom Flex4K

Brands by name

Popular brands