Vision Research Phantom Flex4K Manual Download Page 78

Page: 78 / 94

Phantom Flex4K Manual

connector pin outs

Use these schematics to build custom
cables at your own risk. Mis-wired cables
can cause serious damage to the camera,
which is not covered under warranty.
Vision Research recommends only using
cables supplied by Vision Research.

3-Pin Power

+12-28VDC (Male)

5-Pin Remote (Female)

These pin-out diagrams refer to the con-
nectors on the camera body. Part numbers
indicated are for the cable’s connector.

Main power port
3-pin Fischer part # S-104-Z-040-80

Function

VDC +12-28 VDC

CHGND Chassis Ground

PGND Power Ground

Remote port (for RCU and serial control)
5-pin Fischer part # S-103-A-054-130

Function

+24 VDC

PGND Power Ground

XRXD RS-232 Receive Data +5V maximum,
nomally limited to 16 meters

XTXD RS-232 Transmit Data +5V maximum,
nomally limted to 16 meters

IOGND2 RS-232 Ground - all the serial ports
are not isolated and should only be connected
to properly earthed equipment

Summary of Contents for Phantom Flex4K































































































Search results

Summary of Contents for Phantom Flex4K

Reviews:

Related manuals for Phantom Flex4K

Brands by name

Popular brands

Vision Research Phantom Flex4K, Manual

Search results

Summary of Contents for Phantom Flex4K

Reviews:

Related manuals for Phantom Flex4K

Brands by name

Popular brands