Vision Research Phantom Flex4K Manual Download Page 13

Page: 13 / 94

Chapter 2: Connectors

Standard BNC – For SDI-based viewfinders – Including
the Phantom OLED HD EVF.

4-pin Hirose – For 12V viewfinder or on-camera
monitor power.

7-pin Fischer – Pr12V power and component
signal for viewfinders such as the Sony HDVF35W.
Also works with the Phantom YPRPB cable.

This connector can be factory-replaced with a 20-pin
Hirose for Panasonic viewfinders, contact your sales
rep for more details.

2-pin Lemo – 12V accessory power.

3-pin Fischer – +12 - 28 VDC unregulated
(matches input voltage) auxiliary power + trigger.

12-pin Hirose connector for ENG style lenses.

3-pin Fischer – +12 - 28 VDC unregulated
(matches input voltage) auxiliary power + trigger.

(HD-SDI) Viewfinder

VF PWR

Component VF

+12 VDC

R/S

Lens

R/S

A complete cable connector reference and
pin-out guide is available in the last section
of this manual.

Summary of Contents for Phantom Flex4K































































































Search results

Summary of Contents for Phantom Flex4K

Reviews:

Related manuals for Phantom Flex4K

Brands by name

Popular brands

Vision Research Phantom Flex4K, Manual

Search results

Summary of Contents for Phantom Flex4K

Reviews:

Related manuals for Phantom Flex4K

Brands by name

Popular brands