Vision Research Phantom Flex4K Manual Download Page 68 | Manualshive

Page: 68 / 94

background image

62

Phantom Flex4K Manual

The adjustable arm mounts to the viewfinder, and then
can be adjusted to the desired position on the camera
body. An HD-SDI cable and 12V power cable are also
included and connects to the front left side of the camera.

The full menu system of the Phantom viewfinder can
be found in the included documentation, or online
www.

phantom

highspeed.com/flex4K

The component viewfinder port on the right side of the
camera supplies 12V power and YPRPB component video.
The standard connector is a Fischer 7-pin, which works
with Sony HDVF30, HDVF35W (with a custom cable from
Vision Research) and the Vision Research YPRPB monitor
cable.

There is an option to substitute (factory install) the
7-pin Fischer with a Hirose connector for Panasonic HD
viewfinders.

Shown with standard Fischer connector.

Shown with optional Hirose connector.

«
...
66
67
68
69
70
...
»

Summary of Contents for Phantom Flex4K































































































Reviews:

No comments

Related manuals for Phantom Flex4K

Brand: Canon Pages: 6

DIGITAL IXUS 430

Brand: Canon Pages: 2

Brand: Canon Pages: 28

Brand: Samsung Pages: 98

DMC FX10 - Lumix Digital Camera

Brand: Panasonic Pages: 32

DMCFS12 - DIGITAL STILL CAMERA

Brand: Panasonic Pages: 26

Stylus Verve - Stylus Verve 4MP Digital Camera

Brand: Olympus Pages: 192

Brand: Digitus Pages: 2

ZD15 - Easyshare Zoom Digital Camera

Brand: Kodak Pages: 74

Brand: AgfaPhoto Pages: 32

Brand: COXPAL Pages: 27

Brand: Alinking Pages: 75

Brand: National Geographic Pages: 10

PerfectView CAM301

Brand: Dometic Pages: 180

26164 - Coolpix L20 Digital Camera

Brand: Nikon Pages: 140

Brand: LG Innotek Pages: 25

Brand: MYDLINK Pages: 2

Brand: MYDLINK Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands