background image

received. The counter can be viewed by opening 

the list of alerts in the switchboard. The sending of 

messages never terminates. It continues until the end 

of the service described in the next point, unless the 

switchboard is powered off or removed from the sys

-

tem, in which case the indoor station, after 5 unsuc-

cessful attempts starting from the first timeout of 120 

s, will return to standby mode and the Alert signal is no 

longer sent to the user.

6. If the switchboard operator calls the indoor station 

from the list of warnings, and only from this, a mes-

sage is sent to the indoor station via the Due Fili bus 

to end the Alert procedure so the related signal is no 

longer sent to the user.

Note:  if  the  indoor  station  is  switched  off,  when  it  is 

switched back on again the function starts again from 

the beginning.

Alert Configuration

Use SaveProg to select some of the characteristics of 

the Alert function:

1. Enabling

a. Disabled (default)

b. Enabled

2. Polarity state active

a. Contact normally open (default)

b. Contact normally closed

3. Activation delay

a. 0.1 s (default)

b. 0.5 s

c. 1 s

d. 2 s

4. Signalling mode

a. None

b. LED associated to the

 Stair Light 

key (default)

c. Sound

d. Call Rep. controlling the Call Repeater output of 

the indoor station (terminal 6S).

According to the selected signalling type, apart from the 

first, the timer is as follows:

-  The indoor station waits to receive the alert from the 

switchboard:

  - LED: Flashing with a cycle of 0.5 s on / 0.5 s off

  - Sound: A 2 KHz tone for 0.2 s

  - Call Rep.: Activation with a cycle of 1.6 s on / 1.6 s off

-  The  indoor  station  has  received  confirmation  of  the 

receipt of the message from the switchboard:

  - LED: Flashing with a cycle of 0.1 s on / 0.1 s off

  - Sound: A 1 KHz tone for 0.1 s

  - Call Rep.: Activation with a cycle of 0.4 s on / 0.4 s off

Note

: if the Signalling is set to 

Call Rep.

 and 

Landing

 for 

Alert is enabled, or buttons have been configured for the 

Alert function, then the Call Rep. function of the Indoor 

Station no longer works as repetition for any type of call.

Operation

Calls from an entrance panel, intercom calls and landing 

calls are differentiated by means of different tones.

Entrance panel call

Calls from entrance panels do not correspond to the 

pressing of the call button but are generated internally in 

the entryphone. The call interval is 1 second of ringtone 

and 2 seconds of pause repeated twice (default value 

set on panel). To answer, lift the handset. If the handset 

is already lifted during the call, replace and lift it again. 

The call answer time (30 s) and the conversation time 

(2 minutes by default) are set in the panel parameters. 

When the conversation time has elapsed, the user can 

continue without replacing the handset if a new call is 

made within 10 s from the same panel.

Intercom call

Lift the entryphone handset and press the intercom but-

ton for the entryphone/video entryphone to be called. On 

the calling entryphone handset, a call tone will ring (if the 

call is enabled) or an engaged tone (if not enabled). On 

the called entryphone, the ringtone will start with a cycle 

of 1 second ringing followed by a 4 second pause. The 

maximum duration of the call is 30 seconds (6 cycles). 

To answer the call, simply lift the handset; the maximum 

duration  of  the  conversation  is  5  minutes.  When  the 

conversation time has elapsed, the user can continue 

without replacing the handset if a new call is made within 

10 s. A call from an entrance panel has priority over an 

intercom call.

Missed call from switchboard (enabled 

from SaveProg).

If the function is enabled via SaveProg, the red “Ringtone 

mute” LED signals when there is no answer to a call re-

ceived from a concierge switchboard.

This signal stops whenever a task is performed: answer-

ing a call, making a call or self-starting.

Ringtone mute (User away)

Standard function for entryphone 6209/D. For entry-

phone 6209/P this is only possible by installing acces-

sory 6153/682.

Designed to vary the call volume or to mute the ringtone 

sound. When the ringtone mute is on the red LED is per

-

manently lit. If calls are made from an outdoor station 

to the entryphone when the ringtone mute is enabled, 

they are denied. On the entrance panel, a denied call is 

indicated by means of a dissuasion tone. The message 

“Do not disturb” or “Away” also appears on entrance 

panels with display.

Lock button

On every device, the lock button functions as described 

below.

-  Device with handset in rest position 

 door lock 

function directed to the entrance panel it was last in 

communication with or from which the call was made.

-  Device with handset lifted, but no conversation in prog-

ress 

 call to switchboard if the switchboard flag is 

set to YES. Otherwise the first case applies.

-  Device with handset lifted and intercom conversation in 

progress 

 as in the first case.

-  Device with handset lifted and intercom conversation or 

call from entrance panel in progress 

 door lock 

function directed to the entrance panel with which the 

device is in communication or from which the call was 

made.

In practice, the button always operates the lock release 

except when you lift the handset and immediately press 

the lock button. This too can be set as the standard case 

if there is no switchboard in the system and the switch-

board flag is set to NO.

6. Release the push button to restore to its default value, 

then press it again.

Deleting all settings

This process is recommended when you want to 

change the ID of a previously programmed entry-

phone and you do not want to retain the operating 

programming of the device.

Programming phase (Simplified)

:

1. Lift the handset and bring it to your ear.
2. Press and hold down the lock push button “

” for 6 

s.

3. When the time runs out the indoor station will emit a 

“beep” in the handset (0.5 s).

4. Continue to hold down the door lock push button 

5. After 2 s more the indoor station emits two “beeps” set 

apart (duration 0.5 s with a space in between). 

6. Continue holding down the lock push button “

”. 

7. After 2 s more the indoor station emits a continuous 

tone for 5 s 

8. Release the lock push button “

”.

9. While the indoor station is still emitting a continuous 

tone, press the lock push button “

”.

10. When you release the lock button “

” then press it 

again, three “beeps” will be emitted.

Programming phase (Standard):

1.  Remove the entryphone cover.

2.  Press and hold down the RESET push button on the 

entryphone.

3. Press and hold down push button P1 together with the 

RESET push button.

4. Release the RESET push button, holding down push 

button P1.

5. After 2 seconds the entryphone emits a continuous 

tone for two seconds.

6. Release push button P1.

7. During the continuous tone, press the tab on the lock 

push button.

If the deletion procedure is successful, when the lock 

release tab is pressed the entryphone will emit a triple 

“Beep”.

Alert

Together with concierge switchboard 40510, the indoor 

station creates a system that can send a signal to the 

switchboard operator even when the Due Fili bus is busy. 

The pair of terminals 4-6P (landing call) can be used as 

input. In this case the local landing call function is lost.

Alternatively, you can configure one or more buttons, 

among the eight programmable entryphone buttons 

(P1-P8).

The operating mode is selected using SaveProg.

1. Enable the “Alert” function. See below for the descrip-

tion of the activation possibilities.

2. The indoor station waits to receive the alert from the 

switchboard. In the meantime, the chosen signalling 

is sent to the user according to the table below. On 

receipt of the message, the switchboard emits a dou-

ble beep and displays a red envelope icon to alert the 

operator.

3. If  it  does  not  receive  a  reply,  the  indoor  station  re

-

sends the message every 10 s. After 5 attempts with 

no reply the indoor station stops sending the messag-

es.

4. When an indoor station receives confirmation of the 

receipt of the message by the switchboard, the cho-

sen signalling is sent to the user according to the table 

below. Normally the time between the sending of the 

request and confirmation of reception is less than a 

second.

5. Until the switchboard calls the indoor station to ser-

vice the request, the indoor station resends the mes-

sage every 120 s. At each message, the switchboard 

emits two meets and increases count of messages 

   11

EN

6209/P - 6209/D

Summary of Contents for 6209/P

































Reviews: