Vimar 01913 Instruction Manual Download Page 55 | Manualshive

Page: 55 / 84

background image

53

13.6.3.7 Reading lower temperature alarm settings

This function allows reading the settings associated with the alarm for the temperature being lower
than the value of Tinf�
The SMS message to send is the following one:

<user code>.?AT0

The chronothermostat will send an SMS reply message with the following format:

GSM-01913 1/1

ENABLED:ON/OFF

AT0:XX,X degrees

DTA:X,X degrees

Example�
If the set user code is the default 1234 and:
-  the lower temperature alarm has been enabled;
-  the value of the temperature threshold Tinf has been set to 4�2°C;
-  the value of the temperature differential DTA has been set to 0�5°C;

On sending the SMS message:

1234.?AT0

The chronothermostat 01913 will send the following SMS response message:

GSM-01913 1/1

ENABLED:ON

AT0:4,2 degrees

DTA:0,5 degrees

«
...
53
54
55
56
57
...
»

Summary of Contents for 01913





















































































Reviews:

No comments

Related manuals for 01913

Brand: Taylor Pages: 6

Brand: Danfoss Pages: 20

Brand: Hama Pages: 9

Brand: Danfossss Pages: 40

Brand: Salus Pages: 15

Brand: Salus Pages: 2

QUANTUM SQ610RF

Brand: Salus Pages: 68

Brand: Salus Pages: 64

Brand: L.B. White Pages: 22

Brand: Danfoss Pages: 84

Brand: Alan Pages: 4

Brand: Menuett Pages: 9

Brand: Carrier Pages: 26

Brand: Microlife Pages: 2

Brand: DeWalt Pages: 16

Brand: DeWalt Pages: 160

Brand: Honeywell Pages: 6

Brand: Honeywell Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands