Vimar 01913 Instruction Manual Download Page 68

Page: 68 / 84

13.8.5 Setting manual operation

This function is used to set the chronothermostat operating mode on MANUAL�
To set this mode, send the following SMS message:

<user code>.C1.MAN.XX,X

where

XX,X

represents the temperature to set (at most two whole numbers and one decimal)�

The chronothermostat will send an SMS reply message with the following format:

GSM-01913 1/1

C1 MAN

XX,X degrees

Example�
If the set user code is the default 1234 and you want to set manual chronothermostat operation to the
temperature of 22�5°C, send the following SMS message:

1234.C1.MAN.22,5

The chronothermostat 01913 will send the following SMS response message:

GSM-01913 1/1
C1 MAN
22.5 degrees

13.8.6 Setting automatic operation

This function is used to set the chronothermostat operating mode on AUTOMATIC�
To set this mode, send the following SMS message:

<user code>.C1.AUTO

The chronothermostat will send an SMS reply message with the following format:

GSM-01913 1/1

C1 AUTO

Example�
If the set user code is the default 1234 and you want to set the automatic chronothermostat operating
mode, send the following SMS message:

1234.C1.AUTO

The chronothermostat 01913 will send the following SMS response message:

GSM-01913 1/1

C1 AUTO

Summary of Contents for 01913





















































































Search results

Summary of Contents for 01913

Reviews:

Related manuals for 01913

Brands by name

Popular brands

Vimar 01913, Instruction Manual

Search results

Summary of Contents for 01913

Reviews:

Related manuals for 01913

Brands by name

Popular brands