Vimar 01913 Instruction Manual Download Page 77 | Manualshive

Page: 77 / 84

background image

75

13.11 GSM CHRONOTHERMOSTAT CONTROL VIA EASYTOOL PROFESSIONAL LT

SOFTWARE

The GSM chronothermostat 01913 can also be managed with the EasyTool Professional LT software

by connecting the device to a personal computer via the interface 01998�U�

The main functions that the application enables to carry out are the following:

•

User code management�

•

Reading the SW version of the GSM chronothermostat�

•  Managing the telephone numbers for sending the alarm messages�
•   Managing  the associations between the SMS alarm messages and the telephone numbers�
•  Managing the language used in the SMS messages: Italian, English, French, German and Spanish�
•   Managing  the  chronothermostat operating mode: Automatic, Manual, Timed Manual, Antifreeze,

Off and Timed Switch-Off�

• Reading and modifying the time programs for automatic operation�
• Managing the auxiliary output configuration parameters�
•

Managing the input configuration parameters�

•

Auxiliary output test: reading its state and setting its state�

•

Input test: reading its state�

•

Managing the “address” text�

•  Managing the chronothermostat SMS label (default setting C1)�
•  Managing the auxiliary output SMS label (default setting R1)�
•  Managing the input SMS label (default setting I1)�
•  Managing temperature levels: Tantifreeze, T1, T2 and T3�
•  Managing the seasonal mode: heating or air-conditioning�
•  Updating the firmware of the chronothermostat 01913�

Note

: For all the details concerning the procedures for managing the GSM chronothermostat 01913 with

the EasyTool Professional LT program, please see the manual equipping art� 01998�U�

«
...
75
76
77
78
79
...
»

Summary of Contents for 01913





















































































Reviews:

No comments

Related manuals for 01913

Brand: Babycare TENS Pages: 2

Brand: Wattstemp Pages: 4

Altecnic SATK22 Series

Brand: CALEFFI Pages: 12

Brand: Salus Pages: 40

Brand: Young Regulator Pages: 2

Brand: Magnum Heating Pages: 26

Brand: ELEKTRA Pages: 100

Brand: Oakton Pages: 4

Brand: Eastern Energy Pages: 7

Brand: Oakton Pages: 8

TP5000 si range

Brand: Danfoss Pages: 32

Brand: Danfoss Pages: 8

Brand: Gemo Pages: 4

Brand: harmoni Pages: 28

THERMASGARD RTM

Brand: domat Pages: 12

Brand: Fluke Pages: 2

Brand: Sealey Pages: 2

Auto Service Line VS904.V2

Brand: Sealey Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands