Vimar 01913 Instruction Manual Download Page 44

Page: 44 / 84

For the Address text, send the following SMS

<user code>.ADDR.0

where

is the number zero�

Note

: No response SMS message is required from the chronothermostat 01913�

Example�
If the set user code is the default 1234 and you want to delete the Address text, send the following
SMS

1234.ADDR.0

To see (for example, if forgotten) the text associated with the Address Msg� send the following SMS
message:

<user code>.?ADDR

The chronothermostat will send an SMS reply message with the set text:

GSM-01913 1/1

ADDR:

<text ADDRESS>

Example�
If the set user code is the default 1234 and the ADDRESS text is “Mario Rossi via Verdi 44 VICENZA”,
on sending the following SMS message:

1234.?ADDR

The chronothermostat will send the following SMS response message:

GSM-01913 1/1

ADDR:

Mario Rossi via Verdi 44 VICENZA

13.6.1.9 Reading input settings

This function allows seeing the settings associated with the input�
The SMS message to send is the following one:

<user code>.?I1

The chronothermostat will send an SMS reply message with the following format:

GSM-01913 1/1

<customized input label>

ENABLED:ON/OFF

ACTIVE:O/C

TON:<time>ms

TOFF:<time>ms

Summary of Contents for 01913





















































































Search results

Summary of Contents for 01913

Reviews:

Related manuals for 01913

Brands by name

Popular brands

Vimar 01913, Instruction Manual

Search results

Summary of Contents for 01913

Reviews:

Related manuals for 01913

Brands by name

Popular brands