vesper marine WatchMate 650 Owner'S Manual Download | Manualshive

Page: 58 / 67

background image

trigger a CPA alarm. If a target meets the
other specifications for a CPA alarm but is
not moving at least this fast, no alarm will be
triggered.

This setting allows you to indicate that you
don't want alarms for stationary or slow
moving targets.

Selecting “

OFF

” allows a CPA alarm to be

triggered regardless of the target's speed if it
also meets the specifications of the other
settings.

If this setting is lower than the “Target speed
filter” setting a warning is displayed to
indicate you may be filtering more targets
than you intend.

This setting is only available if the “CPA
alarm” setting is not set to “

OFF

”.

CPA alarm - Your
speed

This value specifies the minimum SOG (in
knots) that your vessel must be moving for a
CPA alarm to be triggered by other vessels. If
a target meets the other specifications for a
CPA alarm but your vessel is not moving at
least this fast, no alarm will be triggered.

This setting allows you to indicate that you
don't want alarms when you are stationary or
moving slowly.

- 58 -

«
...
56
57
58
59
60
...
»

Summary of Contents for WatchMate 650




































































Reviews:

No comments

Related manuals for WatchMate 650

Brand: Panasonic Pages: 9

Brand: DANLERS Pages: 2

Brand: Haas Automation Pages: 26

Brand: Xebex Fitness Pages: 15

Brand: qeedo Pages: 2

Brand: IBEX Pages: 4

Brand: Saadat Pages: 61

Brand: Saadat Pages: 22

Brand: Haas Pages: 12

Brand: SaMASZ Pages: 25

Brand: Wasp Pages: 50

Brand: Balanced Body Pages: 4

Brand: Balanced Body Pages: 2

Reformer Trapeze Combination

Brand: Balanced Body Pages: 164

Brand: Wacker Neuson Pages: 50

Brand: Balanced Body Pages: 37

Brand: YASKAWA Pages: 40

RAISED GARDEN BED

Brand: Yardfully Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands