vesper marine WatchMate 650 Owner'S Manual Download Page 5 | Manualshive

Page: 5 / 67

background image

Table of Contents

Trademarks.....................................................................................2
Copyright Notice............................................................................2
Intended Use...................................................................................2
Technical Accuracy........................................................................2
Warnings.........................................................................................3
Glossary..........................................................................................9
Introduction...................................................................................11

Range.......................................................................................12
Bearing.....................................................................................13
Closest point of approach (CPA).............................................13
Time until CPA (TCPA)..........................................................13

Important Information..................................................................14
Specifications................................................................................15
Requirements................................................................................17

GPS Datum..............................................................................17

Installation....................................................................................18

Installing the display................................................................18

Items Needed.......................................................................18

Configuration...........................................................................18

Routing GPS Data Through the AIS Receiver or Using a
Transponder with a Built-in GPS........................................18
Routing GPS and AIS data Direct to the AISWatchMate...19
Configuring each port in setup............................................20
Examining received data.....................................................22

Wiring......................................................................................23

Wiring to an AIS receiver...................................................25
Wiring to a Transponder.....................................................26
Wiring to a Computer..........................................................27
Wiring to a Chart Plotter.....................................................28
Connections to Common Chart Plotters..............................29

- 5 -

«
...
3
4
5
6
7
...
»

Summary of Contents for WatchMate 650




































































Reviews:

No comments

Related manuals for WatchMate 650

Brand: Rangevision Pages: 31

Brand: Velp Scientifica Pages: 12

Brand: Yamaha Pages: 24

Brand: J&M Pages: 33

Brand: J.P. SELECTA Pages: 32

Brand: Xtool Pages: 8

MCX-C15 - MusicCAST Network Audio Player

Brand: Yamaha Pages: 65

Brand: Yamaha Pages: 24

Brand: ubicquia Pages: 36

bionic power knee

Brand: Össur Pages: 2

BALANCE KNEE OM8

Brand: Össur Pages: 36

Brand: Össur Pages: 37

REBOUND DIABETIC WALKER

Brand: Össur Pages: 63

Brand: Össur Pages: 67

ECHODIA Babyscreen

Brand: Électronique du Mazet Pages: 65

Brand: EFX Pages: 2

SHAKER KEEPER 20V 200

Brand: Garland Pages: 84

Brand: Hedson Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands