vesper marine WatchMate 650 Owner'S Manual Download | Manualshive

Page: 54 / 67

background image

To turn the display back on manually, press
any button.

Select “

Disable

” to leave the display on at all

times.

When enabled, this feature reduces power
consumption when there are no targets or
messages to display.

Reset all settings

Resets all settings to the original factory
values. Any settings you have changed will
be reset and you will lose any changes you
have made.

When you select this setting a warning is
displayed. To continue and reset all settings,
choose “

Yes

” to “Are you sure?” and press

“

OK

”.

When you answer “

Yes

” or “

No

”, a message

is briefly displayed confirming your choice.

Settings Associated with Each Profile

The following settings are associated with a profile selection. Each
profile (Harbour, Coastal, Offshore, and Anchor) has it's own value
for each of these settings. The setup screens display the settings
associated with the currently active profile. The name of the current
profile is shown on the top line of the screen. Any changes to these
settings affect the current profile only.

- 54 -

«
...
52
53
54
55
56
...
»

Summary of Contents for WatchMate 650




































































Reviews:

No comments

Related manuals for WatchMate 650

Brand: ParaBody Pages: 5

Brand: Sagola Pages: 20

Brand: Earmor Pages: 5

Brand: K&K Pages: 8

Brand: SAMCHULLY Pages: 48

Brand: Gallagher Pages: 6

Brand: DAKO Pages: 25

Brand: 3M ESPE Pages: 50

Brand: VACGEN Pages: 13

Brand: Hacker Pages: 2

Brand: J.P. SELECTA Pages: 8

Brand: Haemonetics Pages: 134

Brand: Hadeco Pages: 72

Brand: Nellcor Pages: 161

OXIMAX N-600X Series

Brand: Nellcor Pages: 210

Brand: Oase Pages: 120

Brand: OAKWORKS Pages: 24

Brand: L-Acoustics Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands