vesper marine WatchMate 650 Owner'S Manual Download | Manualshive

Page: 48 / 67

background image

again, even after you turn the unit off. You can switch profiles or
make changes to the settings associated with a profile at any time.
To change the settings associated with a profile, you must select the
profile first and then enter setup mode.

Harbour

This profile is intended to be used when navigating within a harbour
where frequent shipping and AIS traffic is expected.

Coastal

This profile is intended to be used when navigating along a coast or
shore where occasional shipping and AIS traffic is usually
encountered.

Offshore

This profile is intended to be used when navigating in open ocean
situations where little shipping and AIS traffic is expected.

Anchor

This profile is intended to be used when anchored or moored and
when you only want to view AIS information from other vessels. By
default, no alarms are enabled in this profile.

- 48 -

«
...
46
47
48
49
50
...
»

Summary of Contents for WatchMate 650




































































Reviews:

No comments

Related manuals for WatchMate 650

Brand: Baileigh Industrial Pages: 40

Brand: J.P. SELECTA Pages: 32

Brand: Palmer Pages: 2

Brand: Ironton Pages: 6

Brand: Y.I.C. TECHNOLOGIES Pages: 6

Brand: neofeu Pages: 28

Brand: Toro Pages: 4

Brand: Martin Pages: 202

Brand: KAM Pages: 5

Brand: TECshow Pages: 22

Brand: Vectra Fitness Pages: 18

Indoor Bug Zapper

Brand: TBI PRO Engineering Pages: 2

Brand: Santa Medical Pages: 7

Brand: dbx Pages: 2

Brand: KW Hydraulik Pages: 36

Brand: Qtx Pages: 4

Brand: Amico Pages: 20

Brand: Paloma Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands