vesper marine WatchMate 650 Owner'S Manual Download Page 2 | Manualshive

Page: 2 / 67

background image

Trademarks

AIS

WatchMate

is a registered trademark of Vesper Marine Ltd. All

other product names are trademarks or registered trademarks of their
respective owners.

Copyright Notice

Copyright © 2009, Vesper Marine Ltd.

Unless otherwise indicated, all documentation and operating
software contained within this product or distributed with this
product is copyrighted by Vesper Marine Ltd. All rights are reserved.
Except for short quotations in a review, no portions of this document
or the software contained within this product may be reproduced or
transmitted in any form or by any means without prior written
permission of Vesper Marine Ltd.
Portions of this product use FreeRTOS v5. Source code is available
upon request from Vesper Marine.

Intended Use

This product is intended to be used on leisure or commercial vessels
(excluding IMO/SOLAS class). Vesper Marine has designed and
manufactured this product to be used only aboard vessels.

Technical Accuracy

The information contained in this document is to the best of our
knowledge correct at the time of publication. However, we reserve
the right to change specifications, installation and operating

- 2 -

«
1
2
3
4
...
»

Summary of Contents for WatchMate 650




































































Reviews:

No comments

Related manuals for WatchMate 650

Brand: OMCA Pages: 72

Brand: Barko Hydraulics Pages: 92

Brand: Yamaha Pages: 50

Brand: A&D Pages: 30

Brand: ICELED Pages: 4

Brand: Facom Pages: 4

Brand: FaceLake Pages: 2

Brand: quadient Pages: 14

Brand: Qu-Bit Electronix Pages: 31

Brand: Yamaha Pages: 39

Brand: Yamaha Pages: 110

Brand: VelociRAX Pages: 4

Brand: ABM Pages: 17

Brand: neofeu Pages: 28

VLR100 LED Series

Brand: WE-EF Pages: 3

Brand: Ultrasport Pages: 72

Brand: Wieland Pages: 2

41370 Micro Spot

Brand: SHOWTEC Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands