- 9 -
- Do not walk under the branch after you have made the cut.
- IMPORTANT! Before proceeding with the final cut, check that there are no persons,
animals, or objects in the fall area.
- IMPORTANT! When the branch begins to fall, extract the chain saw from the cut, lay
it on the ground, and leave the area quickly along the escape route.
9. Cutting branches (debranching)
Introduction:
This operation consists of cutting the branches of felled trees.
Note: Do not cut the branches that support the felled tree before cutting it in pieces.
(Fig.2)
- IMPORTANT! Do not climb onto the trunk to cut it.
RECOMMENDATIONS FOR USE (TRIMMING, PRUNING)
- Start cutting the branch with the machine already operating.
- Move the cutting blade away when the machine is still rotating, otherwise the bar
could get blocked inside the branch.
- Work by exerting light pressure on the machine without overloading the motor.
- Cut the branches starting from the lowest ones.
- Use the spike (Fig.A, 11) to help you get closer to the branches that are still entangled
on the plant.
- Wear the shoulder strap.
WARNING: DO NOT USE THE MACHINE WHILST STANDING ON LADDERS OR OTHER
UNSTABLE DEVICES, STAND ON THE GROUND.
MAINTENANCE AND CLEANING
WARNING! All operations indicated below must be carried out with the engine
switched off and the spark plug unplugged.
WARNING! If in doubt, contact an authorised assistance centre.
WARNING! For operations not considered below please seek advice from an
authorised assistance centre.
Take care of your machine and clean it regularly to ensure that it remains perfectly
efficient and has a long lifetime.
Clean the machine with a soft brush or cloth.
Do not spray or wet the machine with water.
Do not use inflammable substances, detergents or solvents as these may damage the
machine beyond repair. The plastic parts are prone to damage by chemical agents.
Periodically lubricate the accessory using the appropriate lubricator (Fig.A, 10).
Bar and chain
- Tension and oil the chain when necessary
- Bring the chain to a specialised workshop for maintenance and sharpening as
needed.
- Turn the bar 180° following extensive use and when the chain is replaced in order to create
uniform wear along the entire bar.
- Lubricate or grease the ball bearings on the nose of the bar regularly.
- Keep the oil channels on the bar clean.
- Replace the chain when, after repeated sharpenings, the length of the tooth has
reached 4 mm or when the links are worn. (Chain type: see technical data)
- Replace the bar if deformed or damaged. (Bar type: see technical data)
- Clean the bar and chain with a degreasing product before a prolonged period of
storage of the machine.
TROUBLESHOOTING
The chain and bar overheat
- Insufficient oil in the tank: fill
- The chain is too tense: loosen the chain.
- Oil nozzle or channel clogged: clean it.
- Adjusting bolt closed: loosen the screw
Chain is dry
- Insufficient oil in the tank: fill with oil
- Adjusting bolt closed: loosen the screw
The chain saw does not cut well, blocks, or makes banging noise
- Chain is loose adjust the chain tension
- Chain is worn: sharpen or replace it.
- Defective chain: replace it.
An oil stain forms under the chain saw
- The chain saw was not cleaned and the sawdust releases the oil accumulated during
cutting: clean the saw and remove the sawdust from the housing.
The bar is loose
- The screws have been fixed badly: make sure that the screws have been tightened
vigourously.
!
Warning! After performing the actions described above, the tool does not work
properly or if abnormalities other than those listed, bring it to an authorized service
center by showing proof of purchase and requesting spare parts. Always refer to
the technical information on the label.
STORAGE
WARNING! Hot surfaces. Some parts of the machine may stay hot for several
hours after it has been switched off. Wait for it to cool down completely before
storing it.
WARNING! Make sure that the storage place is not damp and dusty.
1. Remove all the oil from the tank.
2. Clean the bar and chain with a degreasing product.
3. Put the machine back in a firm, safe position, out of the reach of children.
DEMOLITION
In order to protect the environment, proceed according to the local laws in force.
WARNING! Before demolition totally empty the tank.
Do not throw the packaging away. Take it to a recycling centre instead.
When the machine is no longer usable or reparable, dismantle the various parts for
differentiated refuse collection.
All the plastic components bear an acronym identifying the materials they are made
of. This can be used when recycling them in the future.
Do not dispose of used oil with domestic waste, but take it to the special Collection
Centres.
WARRANTY
The product is protected by law against non-compliance with the declared characteri-
stics provided it is used only in the manner described in the instructions, it has not been
tampered with in any way, it has been stored properly, has been repaired by authorized
and, where applicable, have been used only original spare parts.
In the case of industrial or professional use or when using such a guarantee is valid
for 12 months.
To issue a claim under warranty you must present proof of purchase to your dealer
or authorized service center.
AMENDMENTS
The text, figures and data correspond to the standards in place on the date of printing
the instructions contained herein. The manufacturer reserves the right to update the
documentation if changes are made to the appliance, without being bound by any
obligations.
© No part of this publication and the documentation enclosed with the machine may
be reproduced without written permission from the manufacturer.
Summary of Contents for 1491964
Page 3: ... 3 ...
