56K Softmodem
Command Reference
- 24
Table 3-31: &T<value> Commands
&V<value>—Display Current Configuration
Use this command to display the current 56K Softmodem configuration. The
modem maintains two stored profiles and the active profile. This command
displays all three configurations and any stored telephone numbers.
Result codes:
OK
if <value> = 0.
ERROR
if <value> does not equal 0.
The following is an example of the
AT&V0
results.
ACTIVE PROFILE
:
B1 L2 M1 E1 N1 Q0 V1 W2 X1 Y0 &C1 &D2 &G0 &J0 &K3 &L0 &Q5 &S0
%C3 %E2 \J
0
S00:001 S01:000 S02:043 S03:013 S04:010 S05:008 S06:003 S07:060 S08:00
2
S09:050 S10:014 S11:095 S12:050 S14:138 S18:000 S20:000 S21:048 S22:02
2
S23:008 S27:073 S28:160 S29:050 S30:000 S31:010 S32:010 S33:000 S35:00
0
S36:007 S37:000 S38:002 S39:003 S40:040 S41:107 S42:001 S43:001 S48:00
7
S49:027 S50:015 S51:095 S52:007 S53:047 S54:002 S55:035 S56:000 S57:00
0
S58:030 S60:255 S61:000 S62:000 S63:030 S70:000 S83:005 S90:000 S91:01
0
S92:010 S93:006 S94:000 S95:12
9
STORED PROFILE 0
:
B1 L2 M1 E1 N1 Q0 V1 W2 X1 Y0 &C1 &D2 &G0 &J0 &K3 &L0 &Q5 &S0
%C3 %E2 \J
0
S00:001 S01:000 S02:043 S03:013 S04:010 S05:008 S06:003 S07:060 S08:00
2
S09:050 S10:014 S11:095 S12:050 S14:138 S18:000 S20:000 S21:048 S22:02
2
S23:008 S27:073 S28:160 S29:050 S30:000 S31:010 S32:010 S33:000 S35:00
0
S36:007 S37:000 S38:002 S39:003 S40:040 S41:107 S42:001 S43:001 S48:00
7
S49:027 S50:015 S51:095 S52:007 S53:047 S54:002 S55:035 S56:000 S57:00
0
S58:030 S60:255 S61:000 S62:000 S63:030 S70:000 S83:005 S90:000 S91:01
0
S92:010 S93:006 S94:000 S95:12
9
STORED PROFILE 1
:
Command Function
&T0
Abort. Terminates the test in progress.
&T1
Initializes local analog loopback, V.56 Loop 3. If a connection exists when this command is
issued, the modem hangs up. The modem displays the
CONNECT <rate>
message at the
start of the test.
&T3
Local digital loopback test, V.54 Loop2. If no connection exists, the 56K Softmodem returns
ERROR
.
&T6
Requests a remote digital loopback, V.54 Loop 2 without self-test. If no connection exists,
the 56K Softmodem returns
ERROR
and generates the
CONNECT<rate>
result code.