TSUJI ELECTRONICS PM16C-16HW2 User Manual Download Page 48

Page: 48 / 75

7 Commands for parameter set up

<ch>: 0 ~ F(Hexadecimal) for channel.

Command HOLD?<ch>

Confirm the output of hold off signal.

OFF/ Enable the output of hold off signal.
ON/ Disable the output of hold off signal.

Example HOLD?3 reply: ON CH3’s hold off signal has disabled.

Remarks

Command H_ONTM<ch><t>

Set the time from excitation to the motor to actual movement.

Argument < t >

Excitation
time

Setting range: 50 to 3000 msec.
Initial value in 10ms increments 80msec.

Reply None

Example H_ONTM7500 Channel 7 operates 500ms after the holdoff is released.

Remarks Only remote mode.

Command H_ONTM?<Ch>

Check the time from exciting the motor to the actual movement.

Reply DDDmsec.

Example

H_ONTM? A Reply: 100 msec. Channel A will start operating 100ms after the holdoff is
released.

Remarks

Command

H_OFTM<ch><t>
HOLDTM<ch><t>

Set the time to output the hold-off signal after the motor has stopped.
Both commands have the same behavior.

Argument <t>

Excitation
time

Setting range: 50 to 3000 msec.
Initial value in 10ms increments 500 m sec.

Reply none

Example H_OFTMC1200 Channel C outputs a holdoff signal 1200ms after it has stopped.

Remarks Only remote mode.

Command

H_OFTM?<Ch>
HOLDTM?<Ch>

Check the time to output the hold-off signal after the motor has stopped.
Both commands have the same behavior.

Reply DDDmsec.

Example

H_OFTM? 5 Reply: 1000 msec. Channel 5 starts operation 1000ms after the holdoff is
released.

Remarks

Summary of Contents for PM16C-16HW2












































































Search results

Summary of Contents for PM16C-16HW2

Reviews:

Related manuals for PM16C-16HW2

Brands by name

Popular brands

TSUJI ELECTRONICS PM16C-16HW2, User Manual

Search results

Summary of Contents for PM16C-16HW2

Reviews:

Related manuals for PM16C-16HW2

Brands by name

Popular brands