TSUJI ELECTRONICS PM16C-16HW2 User Manual Download Page 53

Page: 53 / 75

7 Commands for parameter set up

7-6 Setting of the home position related

<ch>: 0 ~ F(Hexadecimal) for channel.

Command SETHP<ch>0<hpf><hpd><atd>

Change How to set the home position, and rewrite
the detection situation.

Argument

<hpf>

state of home
position

0/ not found 1/ found

<hpd>

direction of
home position

0/ CW 1/ CCW
Record the direction that had been moved when detects the
home position.

<atd>

direction of start
of automatic
home position
detection

0/CW 1/CCW
If the home position is not set, this is the direction to move
first when the automatic home position is detected.

Reply Nothing

Example SETHP00001 CH0, hpf is “not found”, hpd is CW, atd is CCW

Remarks

Only remote mode.
Item that is shaded is the default settings at parameter reset.

Command SETHP?<ch>

Confirm the information of the home position, and how to set the home
position.

Reply 0<hpf><hpd><atd> refer to ”SETHP” for meaning.

Example SETHP?2 reply: 0110 detected the home position.

Remarks

Command SHP<ch><pos>

Normally the home position data is automatically set by HP mode, but
this command changes the data by force.

Argument <pos>

position -2,147,483,647 ~ +2,147,483,647

Reply Nothing

Example SHP5+10000

Set 10,000 to CH5’s home position.

Remarks Only remote mode.

Command SHP?<ch>

Read out the home position data.

The home position was found. /

ddddddd(Signed Integer 7-digit and more)

The home position was not found. / NO H.P

Example SHP?5 reply: +0010000

Remarks

Summary of Contents for PM16C-16HW2












































































Search results

Summary of Contents for PM16C-16HW2

Reviews:

Related manuals for PM16C-16HW2

Brands by name

Popular brands

TSUJI ELECTRONICS PM16C-16HW2, User Manual

Search results

Summary of Contents for PM16C-16HW2

Reviews:

Related manuals for PM16C-16HW2

Brands by name

Popular brands