TSUJI ELECTRONICS PM16C-16HW2 User Manual Download Page 69 | Manualshive

Page: 69 / 75

background image

10 Firmware version up

68

6.

Operation is Tera Ter’s File -> Send file, and then the window displays a screen to select
a file to send.

Choose the text file of version up that you prepared in the above section 1
(16CHW2_V1.xx.S). Upload will begin.
Depending on network conditions, it may take some time to send the file.
In that case, increase the window size of Tera Term.

7.

REM lamp on the PM16C-16 is blinking on and off slowly that indicate receiving the file
by PM16C-16HW2.
After received all data, REM lamp turns on quick blinking mode. Then the data write
procedure begins.
After finishing data write procedure to ROM, REM lamp turns off. And then LOC lamp
turns on.
Program upgrade procedure is finished.

8.

Please disconnect the Tera Term and exit.
Restart the main unit, or enter the "REST" command, it will start with the new version.

You can use the "FIRMWARE CHANGE" on Page11 at SETUP mode, to switch the
firmware you want to use.

NEW: Firmware that you downloaded to the last.
OLD: Firmware that you have downloaded to 2 times before.

Remark:
The position data will be set to all zero if the firmware is changed and started. (Switched
the firmware to be used in the "PROGRAM CHANGE". Or, downloaded the latest
firmware.)

If trouble occurred in download process, when power on the unit again, sometimes program
runs out of control.
Initial display character isn't correct. In this case, please power off and power with pushing
ten-key "8" switch.
The unit runs from previous ROM version again. And you can try again upgrade procedure.

This method is useful at any time, but the display "NEW","OLD" those are shown in LCD
display in SETUP mode will not be changed. “NEW”,”OLD” display changes after V1.08.

Even if by the above operation, program runs out of control you can start again next
procedure.
There is an original program in CPU-ROM.

When you use this mode you have to pay attention to following procedures.

Please be careful about an electrical shock, when you have opening the cover of this unit.
First take out power cable of it.
If you have some troubles to do next procedure, please contact us.

«
...
67
68
69
70
71
...
»

Summary of Contents for PM16C-16HW2












































































Reviews:

No comments

Related manuals for PM16C-16HW2

Brand: Watts Pages: 2

Brand: Canon Pages: 2

Brand: OmarLift Pages: 14

Brand: UNITED Pages: 8

Brand: Samson Pages: 52

Brand: J3C Pages: 2

Brand: Sanhua Pages: 3

Brand: OES Pages: 3

Brand: Pando Pages: 43

Grafica DNE-K07

Brand: Paradox Pages: 24

Brand: Panosol Pages: 105

Brand: Pangolin Pages: 8

Brand: Ziton Pages: 36

Brand: Nemesis Pages: 6

767-4803/000-800

Brand: WAGO Pages: 80

Vertical Fan Coil

Brand: Solaris Pages: 10

Brand: S&C Pages: 24

Brand: Quickie Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands