Triumph Adler LP 210 Instruction Handbook Manual Download Page 144

Page: 144 / 162

Troubleshooting

10-14

Laser Printer 200 Series

10.3

General print problems

Problem

Possible cause

Action

No output

The printer is not connected to
the power supply, or the cable is
not connected to the printer.

Check the power connection and
the interface connection to the
printer.

The printer is not switched on

Switch the printer on.

You are using the wrong type of
interface cable.

Check whether the interface
cable type conforms to the
specifications, see page 11-4.

The connection settings were
not made correctly for your
printer.

Check the connection settings of
the printer.

The parallel port on your
computer is also being used for
other equipment (e. g. scanner,
ZIP drive).

Disconnect the other equipment
and operate the printer via this
port.

Summary of Contents for LP 210



































































































































































Search results

Summary of Contents for LP 210

Reviews:

Related manuals for LP 210

Brands by name

Popular brands

Triumph Adler LP 210, Instruction Handbook Manual

Search results

Summary of Contents for LP 210

Reviews:

Related manuals for LP 210

Brands by name

Popular brands