Triumph Adler LP 210 Instruction Handbook Manual Download Page 30

Page: 30 / 162

Unpacking, installing and setting up the printer

2-14

Laser Printer 200 Series

Printing out the configuration page

The configuration page should be printed out in order to ensure that the
printer is operating correctly.

Switch on the printer.

The printer is ready for use after
approx. 23 seconds.

Make sure that:

❍

the “Fault“ and “Paper“ lamps
are off, and

❍

the “Stand-by“ lamp is on (but
not flashing).

Briefly press the control button.

The configuration page is printed
out.

✎

Be prepared for technical inquiries!
Always have a current configuration page available in the event of a
technical inquiry. Make a note of the printer‘s serial No. on the
configuration page, see page 1-7 (Safety label).

Control button

Summary of Contents for LP 210



































































































































































Search results

Summary of Contents for LP 210

Reviews:

Related manuals for LP 210

Brands by name

Popular brands

Triumph Adler LP 210, Instruction Handbook Manual

Search results

Summary of Contents for LP 210

Reviews:

Related manuals for LP 210

Brands by name

Popular brands